Door Videos and Transcripts
How We Pack Your Orders
How We Pack Your Orders Video Transcript
Welcome to our warehouse, in this video we are showing you how we pack up your orders and keep items safe during transit.
High quality, heavy duty packing tubes are used for longer items such as tracks, ensuring the contents are secure and protected.
When packing our orders, we use cardboard bubble wrap and reuse cardboard boxes in order to be as eco-friendly as possible.
Some larger items like pocket door kits are boxed up and covered in a shrink wrap bag. We use a heat gun to shrink the bag around the box for protection.
Small orders are sent in reused boxes, and cardboard bubble wrap is added for protection. The boxes are then taped up using distinctive red packing tape.
A label is stuck on to every order reminding customers to check their parcels before signing.
Longer items such as tracks for sliding doors are sent in tubes. Tracks with special finishes are wrapped in bubble wrap before being put in tubes.
Components are taped to the tracks to avoid damage and missing parts. The tubes are then sealed with heavy duty staples and red tape at each end.
Even longer tracks up to 6 meters in length are taped together and attached to a long piece of timber for added strength.
Components are then taped on and everything is placed in to a long tube. Each end is protected with bubble wrap and sealed off.
When using Jiffy bags, more fragile items are first put in a bubble wrap bag and then placed in to the jiffy bag for extra protection.
EXIDOR panic hardware
EXIDOR panic hardware Video Transcript
Exidor have produced three different versions of their 200 series panic hardware over the years. The spares of which are all available on our website.
I will now go through how to identify which version you have fitted.
The Mark 1, which has a flat top, takes the oval bar through an oval hole on the handle. The oval bar is secured with a grub screw in the bottom.
The Mark 3, is very similar to the mark 1 the main difference being that it has a radius top. It still has the oval hole for the oval bar which is also secured with a grub screw. The Push bar which has a corresponding hole in it is located into the oval hole the end cap is then placed in the end, the grub screw is then tightened and as the grub screw goes through the hole, it tightens onto the end cap, ensuring that the end cap and bar are firmly held in the panic hardware.
The Mark 2, is similar to the Mark 3 by having a radius top but, it doesn't have a complete oval for the bar to go in, it has an open section in the bottom. The bar is held in with a black plastic end cap and secured with a screw. The push bar is placed into the receiver, the end cap is placed over and the screw is tightened. Thus, holding the push bar in the panic hardware.
Geze TS3000 - Advantages and Disadvantages of Guide Rail Door Closers
Geze TS3000 - Advantages and Disadvantages of Guide Rail Door Closers Video Transcript
Here we're looking at the Geze TS3000 guide rail door closer and we'll be talking about the advantages and disadvantages of guide rail type of door closers.
Advantages
So, the arm is vandal resistant, meaning if people were to swing on the arm it just disengages from the guide rail not causing damage to the body and at a later date you could just pop it back in.
The door closer has a lower profile than most other systems as you can see the arm doesn't stick out so it can go almost flat against the door. It can be fitted hinge side and opposite hinge side.
The guide rail can be fitted to the underside of a frame or reveal using an extra bracket. Here you can see behind the slide plate adjustment screws for the speed of the opening and other things like back check. Go and see our other video link below to see how to adjust all of those items.
The door closer can have an additional mechanical hold open and back check, you don't need to wire power to the device. If you're using the mechanical hold open it is not to be used on fire doors. If you do need to have hold open on a fire door you need to have it powered, but you don't need power to go to the body on the door you just need power to the guide rail on the frame. This is much easier to wire to.
Disadvantages
With the guide rail door closers, the opening angle is restricted to 120 degrees meaning you can't get the full 180 degree opening.
The guide rail options are often more expensive than the scissor arm door closers. For the guide rail door closers there's less adjustability in the position of functions like back check and delayed action this means there is a smaller angle where these actions will take place as the door closes.
GEZE TS4000 door closer - Fitting & Adjusting
GEZE TS4000 door closer - Fitting & Adjusting Video Transcript
I'll now show you how to adjust the TS-4000 door closer.
Position arm
The most important first thing is to make sure the arm is fitted on the spindle in the correct position that is 80 degrees towards the hinge side of the door.
Once you've ascertained that we need to pre-load the door slightly on the arm to make sure it shuts tight into the frame. This is done by pushing the arms up very slightly towards the middle of the door and just tighten it so that we know that it's clear and hard into the frame as you can see there. Then we can remove the cover once we've ascertained that's correct as such to adjust the closer.
2.Power setting
First thing we need to do is adjust the close door closer to suit the width of the door. This is done by adjusting the valve here. There's a window in the front with an indication of the size. You need to look at your fitting instructions for the correct width of door and adjust this window accordingly by either clockwise or anti-clock clockwise turning.
When you've got that roughly about right then you can try the door and then just set it up to make sure it shuts into the frame properly etc by fine adjustment of this adjustment.
Then we need to look at the closing and latching speeds. The overall closing speed is adjusted by one valve at the end of the closer marked 180 to 0 degrees (If you are adjusting a TS4000 S this screw will be labelled"70 - 0").
3. Closing speed
This is done by turning clockwise to slow and anti-clockwise to speed up the closer as it shuts.
4. Latching action
Latching action is adjusted by position of the arm and for this we need a 10 mil' spanner which adjust the arm hit as such normal, as I said this is why this is critical, this is normally 80 degrees to increase that gives you full latching action, to decrease latching action you move it to the top arm is at 90 degrees to the door and tighten, you will find there is no latching action on the door. If you want a variation in between just loosen the arm and vary between those, those two positions and tighten and you'll get less or more action as needed (If you are fitting the TS4000 S, you will find two additional adjustment screws on the body of the closer, on labelled "10 - 1" for latching action and another labelled "180 - 70" for delayed action feature. Please consult your TS4000 S fitting instructions for how to set these features).
5. Back check
Finally, we need to adjust the back check which is done by the valve marked BC OD here to increase the back check, that is the braking action on the door. Turn the valve clockwise to decrease the action. Turn it anti-clockwise. When fully on the door will brake as you can see there. And finally, just clip the cover on.
How to fit our door handles
How to fit our door handles Video Transcript
First of all, before you start fitting your lever handles you need to ensure that the latch that you've got in your door comes with the appropriate holes for the bolt through fixings. If not, these are available here as part of our latch sets.
Take the latch and fit it into the door. Ensuring that the latch bolt itself is correctly orientated for the handle of your door. And then screw it in.
Next take the spindle and place it into the latch roughly halfway. You will notice on spindle that there is a hole. This is for the grub screw which is on these particular levers placed at the bottom of the lever to pierce through the spindle to give you another good fixing point.
Take the lever and holding the spindle, place the lever over the spindle and push it on.
Take your Allen key and tighten up the lever so it's holding the spindle firm. For this demonstration we're using our duckbill lever which is one of our most popular models.
With the lever in place, you can now mark with a pencil the two bolt through fixing holes. Remove the lever and the spindle combination in one go.
You can now drill your door for the two bolt through fixing holes, which I've already pre-done here, and take your lever and spindle and place it back into the latch bolt.
Take your other lever and place it on the other side of the door, pushing onto the spindle.
Now take your bolt through fixing kit which comes with this, with the levers, place it through the door and put on the other side, bolting the two halves of the lever sets together.
Now take the second bolt through fixing and feed it through your handle. This can be a little bit fiddly. And now tighten up both bolt through fixings and ensure the levers are securely attached to the door.
Next take the screws that come with the kit and place them into the top and bottom screw hole. This allows the lever to be held firmly in position on the door whilst the bolt through fixings hold the lever so it doesn't come off the door.
Take your Allen key and finally adjust the grub screw underneath the lever handle and you'll feel it go very stiff, and then all of a sudden, it'll go very loose. That means that you've pierced the hole that's in the spindle.
And just continue to do that up until it becomes reasonably firm. Final thing to do is to take the rose cover slip it over the end of the lever handles, push it on and clip into place and there you have assembled your lever furniture.
How to Identify Your Door Closer
How to Identify Your Door Closer Video Transcript
Hello. In today's video I will be showing you the ways in which you can identify the door closer you have in case you need a replacement or if you are buying any spare parts. Here at Doorstuff we stock mainly Geze, Dorma and Exidor door closers. So, in this video we will be looking at these but the same applies to other manufacturers.
The first thing to check is which type closers you have. Do you have a scissor arm, guide rail, concealed or a floor spring.
With the scissor arm closer the arm comes in two parts and either sticks out from the door or can lie flat against the door using the parallel arm bracket.
Guide rail door closers have a track which is normally fitted to the frame of the door and the arm slides in this rail. This gives a much cleaner and neater look on the door.
Concealed door closers are normally cut into the top of the door and the arm and guide rail are in the head of the frame. In order to find which closer you have you need to open the door and look down on the top of the door.
Finally, floor springs are cut into the floor below the door and the door rests upon them with a cover plate to cover over the body of the floor spring.
Identifying the model of the closer
To identify the model of the door closer you need to remove either the cover or the slide plate that is covering over the body of the closer. Once this cover has been removed you should be able to see some numbers or markings that are either stamped, cast or printed onto a label on the body of the door closer. Also there should be a branding or name of the manufacturer of the closer. Numbers such as cpd0069 and en 1154 or en 1155 refer to the tests that the closers have gone through and do not necessarily identify which manufacturer or model of closer you are looking at for the closes that we hold in stock here are where you can find the model numbers. On the Geze closer the model number is cast into the body of the unit. For Dorma closers the model number is normally stamped on one of the ends of the unit. And for the Exidor door closer you can see that the model number is clearly printed on the label stuck to the body of the closer. It is also helpful to know the layout and number of adjustment screws on the closer as this can give us an indication of any extra functions the closer might have inbuilt.
Extra details such as the size of the body and the en number can also help us narrow down exactly which door closer you have. The en number looks like this if you need any help identifying your door closer feel free to email us a few pictures and we should be able to help. We can also supply spare parts for the door closers that we stock.